• Cement Based, Fast Setting, Waterproofing Material (Waterplug) - WATERSHOCK Cement Based, Fast Setting, Waterproofing Material (Waterplug) - WATERSHOCK

Cement Based Waterproofing Products / Cement Based, Fast Setting, Waterproofing Material (Waterplug)

WATERSHOCK

Description

Cement-based, reinforced with mineral filler, special additives and polymers, quick-setting, one-component waterproofing material that instantly stops running water through holes or cracks in concrete or masonry. It expands as it sets to lock into place even under constant water pressure.

Fields of Application

  • Repairing static cracks.
  • Waterproofing of active water leak.
  • To block water leak before waterproofing.
  • To chamfered edge and corner joints and repaired cold joints.
  • In underground and surface structures, sewer systems.

Features and Benefits

  • Easy to prepare and apply.
  • Stops water leaks due to the fast setting property.
  • Works as a water leak plug with expanding volume.
  • Resistant to corrosion.
  • Non-toxic. Safely us in water tanks.
  • Topcoat insulation material can be applied within a short time after application.

Application Procedure

Preparation of Substrate

The application surface must be clear, durable and clean off any dirt, dust, paint, mud, etc. that may prevent the product from sticking on the surface. The cavities, cracks, or the leakage points from which the active water leakage occurs must be opened up to the solid ground. The surface must be dampened before the application.

Application Method

WATERSHOCK is added into the clean container, added specified amount of water and mixed by hand until getting homogenous blend. 5 kg WATERSHOCK should be mixed with 1,20 - 1,40 lt clean water. It is absolutely necessary to wear rubber glove during this process. Do not mix exceed 30 seconds. For stop active water from running through concrete and masonry, cut out cracks or hole to until reaching solid. During the mixture stirring, mortar gets warm. Warmer mortar is shaped manually by hand, pressed into the region to be plugged firmly and held until it becomes rigid. Do not remove hand pressure too soon so as to provide some confinement to WATERSHOCK expansion during its set. Do not twist the material during placement or disturb during set time. To stop leaking mortar joints or static cracks in below-grade masonry and concrete walls, cut out defective mortar joints or cracks to deep enough and then WATERSHOCK is filled into opening and keep damp for at least 15 minutes or until a set is fully achieved. To anchor steel bolts or posts in vertical concrete or masonry, drill a hole deep enough and large enough on all sides of bolt or post. Holes must be clean off all dust and dirt particle and dampened. Fill the hole with WATERSHOCK and damp so that entire hole is full. Immediately center bolt or post over hole and force into the putty-like WATERSHOCK. The regions from which too much water leaks or the deep holes can be plugged by applying multiple layers. The mortar application surface must be cooled and cured by damping for 15 minutes after the application.

Consumption

Variable

Package

5 kg plastic bucket

Related Products

Our Products

Our Products

  • Cement-Acrylic Based, Two-Component, Full-Elastic Waterproofing Material - CHIMEX 127

    Cement-Acrylic Based, Two-Component, Full-Elastic Waterproofing Material - CHIMEX 127

  • Cement Based, Set in 3-4 Seconds, Shock Setting Water Plug - TURBOPLUG

    Cement Based, Set in 3-4 Seconds, Shock Setting Water Plug - TURBOPLUG

  • Cement-Acrylic Based, Two Component, Waterproofing Material for Negative-Positive Applications - CHIMEX 227

    Cement-Acrylic Based, Two Component, Waterproofing Material for Negative-Positive Applications - CHIMEX 227

  • Cement Based, Fast Setting, Waterproofing Material (Waterplug) - WATERSHOCK

    Cement Based, Fast Setting, Waterproofing Material (Waterplug) - WATERSHOCK

  • Cement-Acrylic Based, Two Component, Flexible Waterproofing Material for Negative-Positive Application - CHIMEX 235

    Cement-Acrylic Based, Two Component, Flexible Waterproofing Material for Negative-Positive Application - CHIMEX 235

  • Cement-Acrylic Based, Two-Component Semi-Elastic Waterproofing Material - CHIMEX 125

    Cement-Acrylic Based, Two-Component Semi-Elastic Waterproofing Material - CHIMEX 125

  • Cement Based, Crystalized Waterproofing Material - CRYSTAL 25

    Cement Based, Crystalized Waterproofing Material - CRYSTAL 25

  • Cement-Acrylic Based, Two Component, Flexible, UV Resistant, Waterproofing Material - CHIMEX 233

    Cement-Acrylic Based, Two Component, Flexible, UV Resistant, Waterproofing Material - CHIMEX 233

Construction Chemicals