• Cement Based, Structural Repair Mortar - REPAMERK 301

Repair and Reinforcement Systems / Cement Based, Structural Repair Mortar

REPAMERK 301

Description

REPAMERK 301 is a cement based, single component, polymer and fiber reinforced, thixotropic structural repair mortar with high strength. REPAMERK 301 PG is a pouring grade structural repair mortar.

Fields of Application

  • To repair of the reinforced concrete elements,
  • To protect concrete against sulphate and chlorine,
  • To repair and protect underground structures,
  • Structural and non-structural repairs of high strength concrete elements
  • To repair light and medium traffic floors,
  • To repair the tie-rod and cone holes.

Features and Benefits

  • Non- shrink.
  • Applicable as 10-40 mm thickness at one layer.
  • Perfect bonding to the concrete and steel.
  • High compressive strength.
  • Does not sag due to the thixotropic behavior.
  • Waterproof.
  • Resistant to chloride, sulphate and oils.
  • Easy to apply, mixed with only water.

Application Procedure

Preparation of Substrate

Concrete surface must be sound, clean and dry. Surface must be clean off dust, dirt, rust, oil and all contaminants. If there is a water leakage, it must be drained or properly plugged. Concrete surfaces must be saturated with water before application. Immediately before pouring, surface should be wetted, then remove all excess or standing water from within any formwork.

Application Method

25 kg REPAMERK 301 is poured into maximum 4 liters of water and mix for 3-4 minutes under low speed mixer until having a homogenous consistency. Let the mortar have rest for 4 minutes and re-mix for 30 seconds. Prepared mortar should be applied within 30 minutes in 20°C. REPAMERK 301 is applied on the surface by using a steel trowel or spray gun. Application thickness should be between 10-40 mm. If needed second coat should be applied after 24 hours in same way. If required more smooth finish, water should be sprayed onto the mortar and the surface should be finished with using steel or wooden trowel. Application surface must be protected from the rain, wind, frost etc. during first 24-48 hours after finishing repair.

Consumption

For 10 mm thickness approximately 19,20 kg/m² is required.

Package

25 kg kraft bag

Related Products

Our Products

  • Polyester Based Chemical Anchor - POLY 308

    Polyester Based Chemical Anchor - POLY 308

  • Epoxy Based, Two Component, Solvent-Free, Anchoring and Adhesive Mortar - EPOX 305

    Epoxy Based, Two Component, Solvent-Free, Anchoring and Adhesive Mortar - EPOX 305

  • Cement Based, Flowable and Fast Setting Grout Mortar - GRT 25

    Cement Based, Flowable and Fast Setting Grout Mortar - GRT 25

  • Cement Based Grouting Mortar - GRT 20

    Cement Based Grouting Mortar - GRT 20

  • Cement Based, Repair Mortar and Finishing Coat - REPAMERK 2

    Cement Based, Repair Mortar and Finishing Coat - REPAMERK 2

  • Polyurethane Based, Two Component, Injection Resin - PUR IN 24

    Polyurethane Based, Two Component, Injection Resin - PUR IN 24

  • Cement Based, Structural Repair Mortar - REPAMERK 301

    Cement Based, Structural Repair Mortar - REPAMERK 301

  • Corrosion Protection and Bonding Agent Mortar - REPAMERK 325

    Corrosion Protection and Bonding Agent Mortar - REPAMERK 325

  • Epoxy Based, 3 Component, Solvent-free, Repairing and Filling Mortar - EPOX 310

    Epoxy Based, 3 Component, Solvent-free, Repairing and Filling Mortar - EPOX 310

  • Epoxy - Acrylate Based Chemical Anchor - EPOX 307

    Epoxy - Acrylate Based Chemical Anchor - EPOX 307

  • Cement Based, Repair Mortar for Non-Structural Repairs - REPAMERK 1

    Cement Based, Repair Mortar for Non-Structural Repairs - REPAMERK 1

  • Epoxy Based, Two Component, Solvent Free, Adherence Between Old and New Concrete - EPOX 311

    Epoxy Based, Two Component, Solvent Free, Adherence Between Old and New Concrete - EPOX 311

  • Mold (Fungus) Preventive Impregnation Primer - WALL CL 100

    Mold (Fungus) Preventive Impregnation Primer - WALL CL 100

  • Reinforcing Purpose, Epoxy Based Injection System - EPOX IN 25

    Reinforcing Purpose, Epoxy Based Injection System - EPOX IN 25

Construction Chemicals