Flooring Systems / Cement-Acrylic Based, Self-levelling High Performance Floor Coating
SELFING 315 is a cementitious acrylic based, steel fibre-reinforced, self levelling, two component, applied with 4-8 mm thickness, high abrasion resistance and elastic industrial floor coating material.
Fields of Application
- Indoor and outdoor areas.
- Factory and warehouse floors.
- Shopping center.
- Car parks and garrages.
- In loading bays.
- Gas stations.
- Balcone and terraces.
- In worn and torn industrial floors used as floor coating.
Features and Benefits
- Provides excellent resistance up to 8 mm thickness application.
- Excellent adhesion to applied surfaces.
- Easy to apply, self levellling.
- Flexible and do not affected vibrations.
- Non- shrinkage.
- Does not affected surface tension that occurred temperature differences.
- Resistant to mechanical influences, water and chemicals.
- Excellent freeze-thaw stability.
Preparation of Substrate
The surface must be dry, sound, moisture free and clear of materials which prevent bonding, such as dust, oil, paint, silicone, curing agents and detergents. Surface temperature should be minumum +10°C. Loose materials on the surface must be removed; cracks on surface must be repaired by proper BAUMERK repair mortar. The prepared substrate should be wetted with water get uniformly saturation, leaving any standing water on surface. Cold joint and small cracks (up to 1 mm) can be filled with SELFING 315.
Part B should be poured into a clean mixed bucket, Part A is added on Part B under electrical mixer. Mixture is stirred 3-5 minutes until get a homogenous mixture. SELFING 315 mixture should be applied as a primer on substrate with bristle brush for obtaining excellent adhesion. Mixture should be applied on wet primer by trowel. After the application, any entrapped air should be released with a spike roller. Under normal conditions, SELFING 315 is ready after 48 hours for pedestrian traffic, after 72 hours for car traffic. 7 days must be waited for heavy traffic conditions.
9,5 kg/m² mixture is used for getting 5 mm thickness.
Total 31,5 kg set
Component A: 25 kg powder
Component B: 6,5 kg liquid
Epoxy-Coal Tar and Solvent Based Coating - EPOCOL 110
Cement-Acrylic Based, Self-levelling High Performance Floor Coating - SELFING 315
Epoxy Based, Two Component, Solvent Free Primer with Fillers - EPOX PR 200
Epoxy Based, Two Component, Solvent Free Floor and Wall Paint - EPOX FL 500
Epoxy Based, Two Component, Solvent Free Primer - EPOX PR 100
Protective and Polisher Coating Material - FH SHINER
Styrene Resin Based, Curing Compound and Surface Protector - CURE R
Water Based, Epoxy Floor and Wall Coating - EPOX FL 600 W
Cement Based, Self Levelling Flooring Compound (3-10 mm) - SELFING 600
Epoxy-Coal Tar Based, Solvent Free Coating - EPOCOL 220
Acrylic Based, Concrete Curing Compound - CURE A
Plywood Mold Release Agent - MD 150
Surface Hardener and Shiner Material for Cement Based Surfaces - LH 130
Liquid Surface Hardener, Dusting Preventive and Polisher - LH 230
Corundum Aggregate, Concrete Surface Hardener - FH KORUND
Epoxy Based, Two Component, Solvent Free, Orange Peel Textured Topcoat Material - EPOX FL 700
Epoxy Based, Two Component, Solvent Free, Self-levelling Coating Material - EPOX SL 800
Paraffin Wax Emulsion Based, Concrete Curing Compound - CURE P
Mold Release Agent for Wood Mold - MD 100
Bonding Agent for Plaster on Fair Faced Concrete Surfaces - BRUT PR
Epoxy Based, Two Component, Moisture Tolerant Primer - EPOX PR 300
Quartz Aggregate, Concrete Surface Hardener - FH QUARTZ
Steel Mold Release Agent - MD 200
Stamped Concrete Surface Hardener - FH STAMP
Release Agent for Stamped Concrete Systems - FH RELEASE AGENT
Dusting Preventive and Surface Protection Material - LH 415
Polyurethane Based, Two Component, Solvent Free, Self-levelling Coating and Waterproofing Material - PURSELF 201