Flooring Systems / Polyurethane Based, Two Component, Solvent Free, Self-levelling Coating and Waterproofing Material
PURSELF 201 is a polyurethane based, two component, low viscosity, solvent free, elastic, self-levelling coating and waterproofing material.
Fields of Application
- On concrete and cement based mineral surfaces,
- On internal and external applications,
- On factory, storehouse,
- On airplane hangars, tunnels and parking garages
- On shopping malls, markets and restaurants,
- On roof, terrace, ponds and underground water storage.
Features and Benefits
- Excellent adhesion performance.
- Solvent free, safely used in interior surfaces.
- Excellent penetration ability due to low viscosity.
- Covers static cracks.
- Creates jointless and a seamless surface.
- Provides smooth and decorative surface.
- Excellent chemical, mechanical and abrasion strength.
- Easy to apply.
Preparation of Substrate
Application surface must be cleaned off from the contaminant such as dirt, dust, rust, oil etc. Application surface must be scraped to be ready for application. Before the application on an asphalt surface, the surface must be prepared mechanically using abrasive blast cleaning or scarifying equipment to expose at least 50% of the aggregate. Surface should be dry.
Component A and B should be mixed by low speed mixture for 3-4 minutes till homogenous mixture is obtained. Mixture is poured, spread evenly by means of a serrated trowel. After spreading the material evenly, turn the serrated trowel and smooth the surface in order to achieve an aesthetically higher grade of finish. Roll immediately in two directions with a spiked roller to ensure even thickness. Make sure that a continuous, pore free coat covers the substrate.
Mixed product should be applied in max. 30 minutes in about +20⁰C. Waiting time between coats should be minimum 10 hours in +20⁰C and maximum 48 hours. If waited more than 48 hours, the surface should be sanded.
Application must be protected from water, direct sun light, wind, frost and rain at least 1 day.
If necessary, after mixing part A and B, aggregate is added to the mixture as needed and stirred again until a homogeneous mixture is obtained.
19.5 kg component A + 5.5 kg component B = 25 kg set 20.
Epoxy-Coal Tar and Solvent Based Coating - EPOCOL 110
Cement-Acrylic Based, Self-levelling High Performance Floor Coating - SELFING 315
Epoxy Based, Two Component, Solvent Free Primer with Fillers - EPOX PR 200
Epoxy Based, Two Component, Solvent Free Floor and Wall Paint - EPOX FL 500
Epoxy Based, Two Component, Solvent Free Primer - EPOX PR 100
Protective and Polisher Coating Material - FH SHINER
Styrene Resin Based, Curing Compound and Surface Protector - CURE R
Water Based, Epoxy Floor and Wall Coating - EPOX FL 600 W
Cement Based, Self Levelling Flooring Compound (3-10 mm) - SELFING 600
Epoxy-Coal Tar Based, Solvent Free Coating - EPOCOL 220
Acrylic Based, Concrete Curing Compound - CURE A
Plywood Mold Release Agent - MD 150
Surface Hardener and Shiner Material for Cement Based Surfaces - LH 130
Liquid Surface Hardener, Dusting Preventive and Polisher - LH 230
Corundum Aggregate, Concrete Surface Hardener - FH KORUND
Epoxy Based, Two Component, Solvent Free, Orange Peel Textured Topcoat Material - EPOX FL 700
Epoxy Based, Two Component, Solvent Free, Self-levelling Coating Material - EPOX SL 800
Paraffin Wax Emulsion Based, Concrete Curing Compound - CURE P
Mold Release Agent for Wood Mold - MD 100
Bonding Agent for Plaster on Fair Faced Concrete Surfaces - BRUT PR
Epoxy Based, Two Component, Moisture Tolerant Primer - EPOX PR 300
Quartz Aggregate, Concrete Surface Hardener - FH QUARTZ
Steel Mold Release Agent - MD 200
Stamped Concrete Surface Hardener - FH STAMP
Release Agent for Stamped Concrete Systems - FH RELEASE AGENT
Dusting Preventive and Surface Protection Material - LH 415
Polyurethane Based, Two Component, Solvent Free, Self-levelling Coating and Waterproofing Material - PURSELF 201