Terrace, Balcony and Wet-Damp Floor Waterproofing Products / Elastomeric Acrylic Resin Based, UV Resistant, Elastic Waterproofing Material
WHITECOAT is an elastomeric acrylic resin based, single component, UV resistant, ready to use waterproofing material.
Fields of Application
- On inclined terrace roofs,
- On exterior areas for vertical and horizontal applications,
- On concrete, zinc and precast rain gutters,
- On concrete, plaster, brick, tile, gas concrete, wood, galvanized steel, zinc etc. for protecting building against water and moisture.
Features and Benefits
- Single component.
- Ready to use, easy to apply.
- High adhesion strength.
- Creates crack bridge and remains its elasticity.
- UV resistant.
- Water-based, nontoxic, and nonflammable.
Preparation of Substrate
The application surface must be clean, durable and dry, clean off materials which prevent bonding, such as dust, oil, rust and remove loose pieces. Big pores and cracks on the application surface should be filled with REPAMERK 1 or REPAMERK 301 repair mortar. Sharp tips and horizontal/vertical joints which are suitable cracking should be chamfered with REPAMERK 1 repair mortar or PH 127.
WHITECOAT is a ready to use material. Depending on the application surfaces, WHITECOAT should be applied as a primer with thinned by water in the ratio of 1:1 or applied SPR 104. First coat of WHITECOAT should be diluted with 20% water, for second coat does not need dilution. If the surfaces that will be walked on have to reinforced with suitable mesh; first layer of WHITECOAT is applied on dry primer with brush or roller. While first layer is wet, apply the fibermesh on it by roll, and ensure that the fibermesh is buried into WHITECOAT. Leave to dry for minimum 2 hours. Then, complete the application of the 2nd layer of WHITECOAT so that the net beneath will be covered completely. Apply the final coat so that the total covering thickness will be completed and leave the covering to dry for one night. Application must be protected from direct sun light, wind, frost and rain in 24 hours. WHITECOAT is not applied on wet and damp surface. Not recommended for water tanks, pools.
0.75 - 1.50 kg/m² for each layer. Recommended at least 2 layers application. Recommended 2 - 3 kg/m² in drain pipes and rain gutters; 3 - 4 kg/m² in terraces.
20 kg plastic bucket
Polyurethane Based, Waterproofing Material for Potable Water Tanks - POLIXA 2
Elastomeric Acrylic Resin Based, UV Resistant, Elastic Waterproofing Material - WHITECOAT
Hybrid-Polymer Based, One Component, Waterproofing Material - HYBRID 120
Polyurethane Based, UV Resistant, One Component, Waterproofing Material - PUR 625
Hybrid Polyurea - PUR 410
UV Resistant, Acrylic-Based, Waterproofing and Heat Insulation Material - SOLARCOAT
Water Based, Transparent Waterproofing and Impregnating Material - TRANSCOAT
Polyurethane Based, Bitumen Modified, Single Component, Liquid Waterproofing Material - PU-B 1K
Invisible Water Repellent and Surface Impregnating Material - SILOX
Polyurethane Based, Two Component, Aliphatic Top Coat - PU TOP 210
Standard Pure Polyurea - PUR 425
Elastomeric Resin Based, UV Resistant, Super Elastic Waterproofing Material - WHITECOAT SP
Modified Pure Polyurea - PUR 426
Polyurethane Based, Transparent, Waterproofing Material - PUR 115
Hybrid Polymer Based, One Component, Transparent Waterproofing Material - HYBRID 115
Polyurethane - Bitumen Based, Two Component, Liquid Waterproofing Material - PU-B 2K
Acrylic Based, Multipurpose Primer - SPR 104
One Component, Polyurethane Concrete Primer - PU 101 A