Cement-Acrylic Based, Two-Component Semi-Elastic Waterproofing Material - CHIMEX 125

Cement-Acrylic Based, Two-Component Semi-Elastic Waterproofing Material - CHIMEX 125

Description

CHIMEX 125 is a cement-acrylic based, two-component, semi-elastic insulation material used on concrete and cement based plasters and applied from the inside and outside against leaking and surface water.

Fields of Application

Features and Benefits

Technical Data

Content



Color

Mixing

Mixture Density

Adhesion Strength

Resistance to Pressurized Water

Capillary Water Absorption

Usage Period

Maturity Period

Application Temperature

Service Temperature

Application Tools

Drying Time

Mechanical Strength

Water Impermeability

Topcoated by plaster/ceramic

Final Strength

HS Code

 : Component A: Polymer modified admixture and special cement

   Component B: Copolymer acrylic dispersion

 : Gray

 : 20 kg A component : 5 kg B component

 : 1,90 g/cm3

 : ≥1,50 N/mm(28 days)

 : 2 bars positive

 : <0,10 g (after 4 hours) (TS EN 12808-5)

 : 2 hours

 : 3-5 minutes

 : +5°C to +25°C

 : -20°C to +80°C

 : Brush


 : 2 days

 : 7 days

 : 3 days

 : 14 days

 : 3824.99.70.00.00

Application Procedure

Preparation of Substrate

The application surface must be durable, clean and clean off materials which prevent bonding, such as dust, oil, rust and remove loose pieces. Big pores and cracks should be filled with REPAMERK 1 repair mortar. Application surface has to be wetted and then waited until it becomes wet/dry. After the first coat of CHIMEX 125, sharp tips and horizontal/vertical joints which are suitable cracking should be chamfered with REPAMERK 1 repair mortar or PH 127 then second coat of CHIMEX 125 should be applied.

Application Method

Liquid component B is poured into a clean container and mix at a low speed and then slowly added CHIMEX 125 powder component A. Continue mixing until obtaining a homogenous mixture without any agglomerate (approximately 3-5 minutes). Mixture should be applied with a brush as 2 or 3 layers. Brush application direction for each layer must be perpendicular to each other. Each layer must be applied after the first layer begin to harden and still wet. Surface should be wetted before second layer. Prepared mixture have to be used within 2 hours. In outer surface applications, the surface has to be protected from sun, wind, frost or rain during the first 24 hours.

Consumption

For each layer, approximately 1,0 - 1,5 kg/m2 mixture is used. Recommended at least 2 coats application, if needed 3 coats might be applied. Product should be applied as maximum 2 mm wet film thickness in single layer.

Packaging

25 kg set

Powder A component: 20 kg kraft bag / Liquid B component: 5 kg plastic drum

Shelf Life

12 months in original, unopened package.

Storage

Store in dry area between +5°C and +35°C. Protect from heat, freezing and direct sunlight.

Cleanup Information

Clean tools and equipment with water immediately after use. Dried material can only be removed mechanically.

Cautions / Limitations

Health and Safety

Warning! Cause eye and skin irritation. If eye or skin contact, get immediate medical attention. If swallowed, do not induce vomiting. Call a physician or poison control center. Never give anything by mouth to an unconscious person.

Wash hands thoroughly after handling. Wear protective clothing, gloves, eye and face protection. Do not eat, drink or smoke when using this product. Take off contaminated clothing and wash it before reuse. Dispose of unused, contents, container and other contaminated wastes in accordance with local, state, federal and provincial regulations.

Keep container closed when not in use. Keep out of the reach of children.

Limited Warranty: This product is subject to a written limited warranty which can be obtained free of charge from BAUMERK Company. Please contact with technical service department for further information and support.

Related Products
Our Products
Contact Us
address
Dursunköy Mah. Uygur Cad. No:44 34555
Hadımköy - Arnavutköy - İstanbul / TÜRKİYE